Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected performance. Fortunately, resetting your Holosun is a simple process that can be performed in just a few procedures.

• First ensuring your red dot sight is powered on.
• Find the small button for reset on the bottom of the sight.
• Use a small object to press and hold the reset switch for approximately 7 seconds.
• Let go the lever and your Holosun EPS Carry Red Dot sight will reboot.
• Your red dot sight should now be set back to its factory settings.

Return to Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it back to standard configuration is a breeze. First, locate the tiny button on the rear of your optic. Then, keep pressed it for around five seconds until you see a brief flash. Your Holosun EPS Carry is now returned to its factory settings, ready for accurate shooting.

revive your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often resolve the problem and get your red dot sight back to its former glory. Before you begin, remember to disconnect the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

• Press and hold the power button for approximately 10 seconds.
• A message will flash, indicating that the reset is in progress.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and test your sight's functionality. If you encounter any further troubles, don't hesitate to reach out to their technical assistance.

Return Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• First, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• During continue holding these buttons, tap the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Holding a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Returned to their default values.

Reinitialize your Holosun EPS Carry through a Factory Standard Settings

If your Holosun EPS Carry is acting funny, a factory reset might be the fix. This will set back your sight to its factory settings, clearing any custom configurations you've made. To perform this reset, adhere factory reset Holosun EPS Carry red dot to these straightforward steps:

• First, find the reset button on your EPS Carry.
• Then, use a fine object, like a toothpick, to push the reset switch.
• As you maintain the reset lever activated, activate your EPS Carry.
• You'll display a message indicating that the reset is complete.

Once the reset is successful, your EPS Carry will be set to its factory settings.

Report this wiki page